--------------------------
Multi-layer sign "open"

Multi-layered Sign

Create your own unique multi-layered sign using TroGlass material using this "how to" guide.

Persiapan

Machine used

You can use any machine in the Speedy range to create these signs.

Tip

Experiment with different colours and textures, or using logos from your customers.

trotec-materials-multi-layer-sign.zip

ZIP

Unduh sekarang

Langkah demi Langkah

Laser cutting TroLase white
Langkah 1

Step 1: Base plate

Import our template and adapt it to your requirements. Send the job of the base plate (bright white) to the laser using the driver settings below:

Process mode Resolution Cut line
Standard 500dpi None
Halftone Others
Color Optimized Geometries, inner geometries first
Laser cut white TroLase ADA
Langkah 2

Step 2: Laser process base plate

The laser parameters may vary depending on the type of laser machine and available laser power.

Color Process Power (%) Speed (%) ppi/Hz
Red Cut CO2 24 0.8 1,000
Passes Air Assist Z-Offset Direction Advanced
1 On - - -
Laser cutting TroLase black
Langkah 3

Step 3: Stripes pattern

Send stripe pattern job and the letters to the laser machine, using the driver settings below:

Process mode Resolution Cut line
Standard 500dpi None
Halftone Others
Color Optimized Geometries, inner geometries first
Laser cut black TroLase ADA
Langkah 4

Step 4: Laser process stripes pattern

The laser parameters may vary depending on the type of laser machine and available laser power.

Color Process Power (%) Speed (%) ppi/Hz
Red Cut CO2 38 0.8 1,000
Passes Air Assist Z-Offset Direction Advanced
1 On - - -
Usage of adhesive tape for laser cutting
Langkah 5

Step 5: Colored layers

Send the colored layers job consisting of TroGlass Frosted and TroGlass Color Gloss to the laser using the driver settings below.

Before cutting the TroGlass Color Gloss and TroGlass Frosted sheet apply adhesive to the back, keeping a minimum of 4cm clear to the top of the sheet - this space is needed for the levitating part and the triangles.

Process mode Resolution Cut line
Standard 500dpi none
Halftone Others
Color Optimized Geometries, inner geometries first
Laser cutting of TroGlass with adhesive tape
Langkah 6

Step 6: Laser process colored layers

Tip: Remove the top protective foil for TroGlass Frosted and TroGlass Satins before cutting.

The laser parameters may vary depending on the type of laser machine and available laser power.

To exactly position the graphic use the green positioning line.

Laser Parameters Color Process Power (%) Speed (%) ppi/Hz
Engraving Black Engraving CO2 16 20 500
Cutting Red Cut CO2 50 0.2 5,000
Creasing Blue Cut CO2 5 1 1,000
Positioning Green Positioning - - -
Laser Parameters Passes Air Assist Z-Offset Direction Advanced
Engraving 1 ON - Bottom Up High Quality
Cutting 1 ON - - -
Creasing 1 ON - - -
Positioning - - - - -
Assembly multi layer sign
Langkah 7

Step 7: Assembly

Start by sticking the stripe pattern on the white base plate. To place it yourself, look for the hole to align it.

Next, make sure the TroGlass Frosted plate is glued exactly on the black ADA.

Following that, comes the TroGlass Color Gloss plate. It is best to position them with the letters at the bottom and to make sure that the area without adhesive foil is exactly positioned. Then the black and green or orange letters are pasted on.

Repeat these steps for the back of the shield. Then, the triangles are inserted into the holes provided.

Finally, a string is feathered through the holes and the multi-layer shield is finished.

Why trotec materials?

Regardless of whether you create individual or standardized signs, Trotec acrylic sheets offer the best solution due to their variety and high-quality workmanship. The TroGlass series is characterized by its extremely tough and scratch-resistant surface. Discover our numerous colors with different surfaces and degrees of transparency.

Seri Speedy
Pengukir dan pemotong laser yang ideal untuk personalisasi.

Temukan pengukir dan pemotong laser

Pertanyaan tentang aplikasi atau pengaturan?
Kami dengan senang hati akan memberikan saran kepada Anda mulai dari A untuk Air Assist hingga Z untuk z-offset.

Hubungi kami
Anggota kebanggaan troGROUP Logo