Covid-19 Signs
Here you will find templates for the quick creation of Covid-19 signs from TroLase, TroLase Foil and TroGlass.
Covid-19 Signs
Here you will find templates for the quick creation of Covid-19 signs from TroLase, TroLase Foil and TroGlass.
Preparation
Materials required
Wash your hand's sign - Variant 1
- 1/4 sheet TroLase black/yellow 1.6 mm L704-206
- 1/4 sheet TroLase blue/white 1.6 mm L512-206 with double-sided adhesive foil on the back
Materials required
Wash your hand's sign - Variant 2
- 1/4 sheet TroGlass reverse glossy/white
- 1/4 sheet TroLase blue/white 1.6 mm with double-sided adhesive foil on the back
- Black acrylic paint
Materials required
Keep your distance sticker
- 1/4 sheet TroLase Foil red/white 0.2 mm
Laser engraving machine used:
- Speedy 300
- 80 watts
- 1.5" lens
- Aluminium cutting grid table or honeycomb cutting tabletop
This sample can be produced with any other Speedy laser engraving machine.
Tip:
When working with TroLase or TroLase Foil, if you are using the entire work surface, a vacuum table or an adhesive mat can be used so that the material lies flat over the entire surface. Otherwise, cover the work surface with paper to create an optimal vacuum.
Step by step
Step 1: Import/Create Print & Laser Template
You can either use our pre-made template or create your own design files. Use the settings below to send the job to the laser.
Important: If you use TroGlass Reverse, the file must be mirrored.
Print settings
Process mode | Resolution | Cut line |
---|---|---|
standard | 500dpi | none |
Halftone | Other |
---|---|
- | Optimised geometries, inner geometries first |
Step 2: Laser engraving and cutting
The next step is to create the parameter settings. Our suggested parameters will differ depending on the laser engraving machine used and the available laser power. Before processing the TroLase and TroLase Foil sheets the protective foil should be removed before placing it into your laser. If TroGlass Reverse is used, we recommend removing the foil after laser processing.
Laser Parameters:
Material | Colour | Process | Power (%) | Speed (%) | ppi/Hz | Passes | Air Assist | Z-Offset | Direction | Advanced |
---|---|---|---|---|---|---|---|---|---|---|
TroLase Foil | black | Laser Engraving CO2 | 55 | 80 | 500 | 1 | off | 1.5 | bottom to top | - |
red | Laser Cutting CO2 | 40 | 1 | 2000 | 1 | on | 0 | - | - | |
TroLase | black | Laser Engraving CO2 | 65 | 80 | 600 | 1 | off | 1.5 | bottom to top | - |
red | Laser Cutting CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - | |
TroGlass Reverse | black | Laser Engraving CO2 | 18 | 20 | 500 | 1 | on | 0 | bottom to top | - |
red | Laser Cutting CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - |
Step 3: Assembly
To attach the parts to each other, first remove the protective film on the back of the blue TroLase shield. Now stick the TroLase label onto the yellow TroLase or the white TroGlass Reverse label according to the markings.
The signs are now ready for use!
These signs can be produced in any colour material.