Laser Cut Holiday Decor: Wooden Christmas Tree with Acrylic Ornament
Create a unique Christmas decoration out of wood, complete with an acrylic bauble! Download your templates and instructions here, and be ready for the festive season.
Preparation
You Will Need
- 1x sheet Solid Wood - Walnut
- 1/4 sheet TroGlitter
- 1x hook for hanging the bauble
Machine Used
- Speedy 360
- 80W
- 2" Lens
- Honeycomb cutting table for wood
- Acrylic cutting grid table for TroGlass
You are free to use any machine from the Trotec Speedy series to create this DIY project.
Step by step
Step 1: Design
Have a go at creating your own design, or feel free to use our template. Send the completed graphic to the laser machine using the following print settings:
Process Mode | Resolution | Cut Line |
---|---|---|
Standard | 500dpi | None |
Halftone | Others |
---|---|
Colour | Optimal Geometries, Inner Geometries First |
Tip:
So that the tree holds well once cutting the base plate, just ensure you measure the thickness of the wooden plate in advance. As a guideline, begin with a cutting gap of approximately 0.2mm when cutting with a 2" lens.
Step 2: Laser Process - Tree
Now it is time to enter the parameter settings. Remember: Parameters may vary depending on the laser machine you are using and its available power.
Laser Parameters | Colour | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|---|
Engraving | Black | Engrave CO2 | 50 | 50 | 500 |
Cutting | Red | Cut CO2 | 95 | 0.8 | 1000 |
Laser Parameters | Passes | Air Assist | Z-Offset | Direction | Advanced |
---|---|---|---|---|---|
Engraving | 1 | ON | +4mm | Down | - |
Cutting | 1 | ON | - | - | - |
Tip:
To achieve a higher contrast in the engraving, lift the Z-Offset to about +4mm.
Step 3: Bauble
You are welcome to use our template and design. But if you're feeling creative, why not design and create your very own bauble? Send the graphics to the laser machine using the following print settings:
Process Mode | Resolution | Cut Line |
---|---|---|
Standard | 500dpi | None |
Halftone | Others |
---|---|
Colour | Optimal Geometries, Inner Geometries First |
Step 4: Laser Process - Bauble
Send the following parameters for the bauble to your laser machine. Please note that the settings may vary depending on the laser machine you are using and its available power.
Laser Parameters: Cutting
Colour | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 50 | 0.2 | 5000 |
Passes | Air Assist | Z-Offset | Direction | Advanced |
---|---|---|---|---|
1 | ON | 0 | - | - |
Step 5: Construct the Tree
Begin by placing the tree into the base plate. Then, hang the bauble from the appropriate tree branch using the hook. Your eye-catching and festive decoration is now ready to display!
"Why are Trotec materials so perfect for this DIY?"
Trotec's engravable woods have been specifically developed for laser processing. Both the Solid Woods and Veneer Woods, as well as the plywood and MDF materials, allow you to achieve fine engraving results and high-quality cuts every time.
Stay tuned! Our TroGlitter range is a type of TroGlass that shimmers and glitters, offering eye-catching results! Lean more about TroGlitter soon.
Inspiration
There are no limits to your creativity...
- Try making the tree even bigger and use it as a statement piece in your home this Christmas
- Browse our range of engraving materials and mix it up a little! You're not just limited to acrylic and wood...
- Try different shapes, graphics and colours for your bauble. You can even personalise your Christmas decorations with names or logos
- Remember - the sky is your only limit!