Trophy with relief engraving
Make a three-dimensional winners' trophy using Trotec materials and 3D relief laser engraving
Preparation
Required material
- 1 sheet solid wood maple
- 1/4 sheet TroGlass Satins black
- 1/4 sheet TroGlass Color Gloss Metallic Silver Anthracite
- Acrylic glue and tissue
- Double-sided adhesive tape and dots
Machine used
- Speedy 360 flexx
- 80 watts
- 2" lens
- Vacuum table with honeycomb cutting table resp. acrylic grid
You can use any other machine of the Speedy Flexx laser engraver series.
Tip
TroGlass Satins and TroGlass Metallic have a very high-end finish
Step by step
Design
Import our template and adapt it to your requirements.
With "Create job" move the design to the "Prepare" screen.
Laser process TroGlass Satins Black
Place the job to the desired position and adapt the settings.
The laser parameters may vary depending on the type of laser machine and available laser power.
Send the job to the "Queue" for Laser processing.
Effect | Engrave Quality |
Process | Engrave |
Layers | black |
Power (%) | 40 |
Speed (%) | 10 |
DPI | 500 |
Source | CO2 |
Air Assist | On |
Z-offset | 2mm |
Passes | 1 |
Power Correction | 20 |
Direction | Bottom up |
Dithering | None |
Engraving Mode | Standard |
Effect | Cut Quality |
Process | Cut |
Layers | blue |
Power (%) | 100 |
Speed (%) | 1.2 |
Hz | 5000 |
Source | CO2 |
Air Assist | On |
Z-offset | 0 |
Passes | 1 |
Power Correction | 7 |
Path planning | Standard |
Effect | Cut Quality |
Process | Cut |
Layers | red |
Power (%) | 8 |
Speed (%) | 0,8 |
Hz | 5000 |
Source | CO2 |
Air Assist | On |
Z-offset | 1 mm |
Passes | 1 |
Power Correction | - |
Path planning | Standard |
Step 3: Laser process TroGlass Metallic
Place the job to the desired position and adapt the settings.
The laser parameters may vary depending on the type of laser machine and available laser power.
Send the job to the "Queue" for Laser processing.
Effect | Engrave Quality |
Process | Engrave |
Layers | black |
Power (%) | 16 |
Speed (%) | 20 |
DPI | - |
Source | CO2 |
Air Assist | On |
Z-offset | - |
Passes | 1 |
Power Correction | - |
Direction | Bottom up |
Dithering | None |
Engraving Mode | Standard |
Effect | Cut Quality |
Process | Cut |
Layers | red |
Power (%) | 50 |
Speed (%) | 0.2 |
Hz | 5000 |
Source | CO2 |
Air Assist | On |
Z-offset | - |
Passes | 1 |
Power Correction | - |
Path planning | Standard |
Laser process Solid Wood Maple
Place the job to the desired position and adapt the settings.
The laser parameters may vary depending on the type of laser machine and available laser power.
Send the job to the "Queue" for Laser processing.
Effect | Engrave Quality |
Process | Engrave |
Layers | black |
Power (%) | 100 |
Speed (%) | 30 |
DPI | 500 |
Source | CO2 |
Air Assist | On |
Z-offset | - |
Passes | 3 |
Power Correction | 20 |
Direction | Bottom up |
Dithering | None |
Engraving Mode | Relief |
Effect | Cut Quality |
Process | Cut |
Layers | red |
Power (%) | 100 |
Speed (%) | 1 |
Hz | 1000 |
Source | CO2 |
Air Assist | On |
Z-offset | - |
Passes | 1 |
Power Correction | - |
Path planning | Standard |
Finishing
Clean the two acrylic pieces with a damp cloth. The wood relief engraving can be cleaned best with some water and a tooth brush. Here you can find tips for correct cleaning.
Put the acrylic glue on the engraved ring of the base plate and position the TroGlass Metallic ring on it. Press down firmly and allow the glue to cure.
Put double-sided adhesive tape or dots where the wooden relief shall be positioned and fix it.
Take the wooden spacer and apply double-sided adhesive tape on both sides. Position it on the left and the right of the black base plate. Make sure to have a rectangular contact surface so that the trophy stands upright.
Finally, fix the lettering "winner" and the corresponding back on the spacers to complete this elegant trophy.
Inspiration
Combine other types of solid wood and TroGlass materials to adapt the trophy to your customers' requirements.