--------------------------
happy birthday card laser cut

Print&Cut Birthday Card

In this tutorial, we show you how to create personalized printed cards with JobControl® Vision Software and camera systems.

happy birthday card laser cut

Print&Cut Birthday Card

In this tutorial, we show you how to create personalized printed cards with JobControl® Vision Software and camera systems.

Preparation

Required material
  • Individually printed paper 200g/m² for the inner part
  • Printed or coloured paper for the outer part at least 300 g/m²
  • Adhesive dots or tape/glue
Machine used

You can also recreate this sample with Speedy 300, Speedy 400 and SP500 with the JobControl® Vision software.

Important
  • To make the card more stable and give it a better stand, use paper with a minimum weight of 150 g/m² for the inner part.
  • Ensure that you send beziers curves to the printer in the driver settings. Otherwise JobControl® Vision can not recognise the registration marks.
Print and cut birthday card

ZIP

Download now
Print and cut birthday card

ZIP

Download now

Step by step

printer settings for laser
Step 1

Step 1: Inner part

You can use our template for the inner part of the card or alternatively you can create your own unique design. To make it even more sentimental, we recommend you adding the name and age of the recipient before printing.

Using the settings below, you then need to send your design to the laser. In this case it is only the registration marks and cutting line. We suggest deactivating the layer with the graphic design so it does not get sent to the laser.

Print settings

Process mode Resolution Cut line
Standard 1000 dpi none
Halftone Others
Color enhanced geometries
inner geometries first
happy birthday card laser cut
Step 2

Step 2: Laser process inner part

Depending on the type of laser machine used and the laser power available, the laser parameters may vary.

Laser Parameters

Laser Parameters Colour Process Power (%) Speed (%)
 RegMark  Black  RegMark  -  -
 Creasing  Red Cut CO2  3,5 2
 Cutting  Blue Cut CO2  7 1
 Cutting  Desert blue Cut CO2  15 4
ppi/Hz Passes Air Assist Z-Offset Advanced
- - - - -
1000 1 on +1.5 mm -
1000 1 on - -
1000 1 on - Correction 20
reg mark laser softwrae
Step 3

Step 3: Positioning of print and laser job

Connect JobControl® with the laser.

Move the job from the queue on the plate and place it in the print position in the laser machine. To do so, you need to move the laserpointer to the middle of any registration mark and then drag the corresponding one to the crosshairs in JobControl®.

Tip:

For easier positioning, use the “What you see is what you get” function (WYSIWYG) in JobControl®.

laser cutting vision software
Step 4

Step 4: Calibrate the camera

First you need to adjust the focus on the paper. In order to calibrate the camera, you need to go to Settings - Options - Hardware - Vision. Ensure that the registration mark stands out from the background. Next move the camera to any registration mark on the print. By using the ideal settings of Exposure, Gamma and Threshold, the circle around the registration mark should be green as well as the bar below the preview. Please adapt these parameters accordingly.

Tip:

Choose fully nonlinear for compensation. By doing so, the software will be able to adjust the job to scaled and rotated prints. 

jobcontrol vision registration marks
Step 5

Step 5: Cutting the job

Once the camera is set up, you may then start your job.

JobControl® will read all registration marks and will automatically cut the job if the position and orientation of the laser job in the software aligns to the position of the material on the working area.

If the two positions do not align, you will need to manually assign the position by placing the camera at the first registration mark. If the bar below the camera preview is green, press Enter to confirm. If the print is distorted, you will need to assign the second registration mark to the correct position. The remaining registration marks will then be read automatically.

assembly of laser cut greetings card
Step 6

Step 6: Outer part

Double-page printed paper was used for the outer part of the card.

Registration marks are not required in this case as no contour cutting is needed.

Next, send your design to the laser machine with the parameters specified below.

Tip:

You can engrave a unique pattern or the name of the recipient on the card to make it extra special.

Print settings

Process mode Resolution Cut line
Standard 500 dpi none
Halftone Others
Color enhanced geometries
inner geometries first
birthday paper popup card
Step 7

Step 7: Laser process outer part

Use our laser paramaters for the outer part. Please note that the parameters may vary depending on the type of laser machine used and the laser power available.

Tip:

If you decide to use another type of paper, be sure to first test the parameter settings on a small section before commencing the actual project.

Laser Parameters

Laser Parameters Colour Process Power (%) Speed (%)
Creasing Red Cut CO2 5 2
Cutting Desert blue Cut CO2 20 3,8
ppi/Hz Passes Air Assist Z-Offset Advanced
1000 1 on +1,5 mm -
1000 1 on - Correction 20
folding paper birthday card
Step 8

Step 8: Finishing

The next step is slightly more difficult - folding the card. Start with the middle fold and then work your way up by folding the cake tiers.

Once you have finished the tiers, put the inner part in the outer card. You can use either adhesive dots, tape or glue.

Tip:

If you wish to fold the card beforehand, for the first try you can cut the job on normal, unrpinted paper (80 g/m²). Just change the process of the Black parameter to "skip".

Inspirations

In a hurry? Try an engraved card instead. You can juse the same design on white or colourful paper. Ensure to use paper with a minimum weight of 150 g/m².

Speedy series
The ideal laser engraver and cutter for personalisation.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Contact us
Proud member of troGROUP Logo