--------------------------
3d sign retro style detail

3D Sign Retro Style

Produce this 3-coloured sign in retro style. By sticking on elements you get quite simply an interesting 3D-effect.

Preparation

Required material
Machine used
  • Speedy 400
  • 120 watts
  • 2" lens
  • Nozzle with large hole
  • Acrylic grid cutting table
DIY Bakery Sign

ZIP

Download now

Step by step

trotec materials laminates
Step 1

Step 1: Import the template

Create your own design or use our template. Now send the job to the laser with the settings below.

Print settings:

Process mode Resolution Cut line
Standard 500 dpi none
Halftone Others
Color optimized geometries,
inner geometries first
laser processing 3d sign laminates
Step 2

Step 2: Laser process TroLase

The above parameters refer to the Speedy 400 model. If you already have a Speedy 400 NEW (with Optimotion) in use, you can set the cutting parameter (red) to power : 50% and speed : 2%. The laser device regulates the required speed automatically.

Now make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.

Remove the protective foil from the top of the TroLase plate. Then place the material on the acrylic grid cutting table in the laser machine. Cover the remaining area to create the best possible vacuum.

Laser Parameters:

Color Process Power (%) Speed (%) ppi/Hz
Black Engrave CO2 35 75 Auto PPI
Red Cut CO2 42 1.2 1000
Blue Cut CO2 20 10 1000
Passes Air Assist Z-Offset Direction Advanced
1 ON 2 Bottom to top Optimized quality, corr. 5
1 ON - - path planning: standard, corr. 5
1 ON - - path planning: standard, corr. 5
Step 3

Step 3: Laser process TroGlass Color Gloss

The above parameters refer to the Speedy 400 model. If you already have a Speedy 400 NEW (with Optimotion) in use, you can set the cutting parameters (red and green) to 80% power and 1.1% speed. The laser device regulates the required speed automatically.

Now make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.

Leave the protective film on the top and bottom of the TroGlass plate. Place the material on the acrylic grid cutting table in the laser machine. Cover the remaining area to create the best possible vacuum.

Cut the TroGlass in two steps: in the first laser process, skip the cutting color green so that the base plate (cutting colors red and blue) is cut first.

Then remove all parts from the laser unit. Now remove the protective film from the back of the remaining plate and apply a double-sided adhesive film instead. Place the remaining TroGlass plate back in the same position in your laser device (adhesive film on the underside). Start the laser process for the cutting color green (lettering), skipping the cutting colors red and blue.

Laser Parameters:

Color Process Power (%) Speed (%) ppi/Hz
Red Cut CO2 30 0.2 5000
Blue Cut CO2 20 10 5000
Green Cut CO2 30 0.2 5000
Passes Air Assist Z-Offset Direction Advanced
1 ON - - Path planning: Standard, corr. 5
1 ON - - Path planning: Standard, corr. 5
1 ON - - Path planning: Standard, corr. 5
3d sign assembly
Step 4

Step 4: Assembly

After the last laser process, remove the individual elements from the laser unit and remove the remaining protective film from the top of all cut parts.

To attach the parts to each other, first remove the protective film from the back of the large TroLase shield. Now stick the TroLase label on the red TroGlass label according to the marking.

Then glue the two smaller TroLase plates ("N. One" and "Freshly baked") to the markings on the large TroLase plate.

In the last step, remove the protective film on the back of the red Troglass lettering. Glue the individual fonts to the upper left edges of the font engravings on the TroLase. The engraving results in a shadow that runs down to the right.

Once all fonts have been glued on, the sign is ready for use!

3d sign retro style inspiration

Inspiration

Choose a color combination for your needs - both the TroLase and the TroGlass are available in different colors in our shop!

Browse full material range

Speedy series
The ideal laser engraver and cutter for personalisation.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Contact us
Proud member of troGROUP Logo