--------------------------
laser-engraving-relief-trophy

Trophy with Relief Engraving

Make a three-dimensional winners' trophy using Trotec materials and 3D relief laser engraving

Persiapan

Required material
Machine used
  • Speedy 360 flexx
  • 80 watts
  • 2" lens
  • Vacuum table with honeycomb cutting table resp. acrylic grid

You can use any other machine of the Speedy Flexx laser engraver series.

Tip

TroGlass Satins and TroGlass Metallic have a very high-end finish

Balloon Trophy

ZIP

Unduh sekarang

Langkah demi Langkah

Druckereinstellungen TroGlass Satins
Langkah 1

Step 1: Import design

You can make your own design or import our template and then adapt it to your requirements. We have engraved a recess out of the base plate to hold the TroGlass Metallic ring.

Printer driver settings:

Process mode  Resolution Cut line
Standard 500dpi none
Halftone Other
colour Optimized geometries
trotec-laser-engraving-troglass
Langkah 2

Step 2: Engraving base plate

Put TroGlass Satin Black on the acrylic grid of your Trotec laser. Engrave and cut the base plate using the parameters below. The parameters can differ depending on the laser machine used and laser power available.

Laser Parameters engraving

Color Process Power (%) Speed (%) ppi/Hz
black Engrave CO2 40 10 500
Passes Air Assist Z-Offset Advanced
1 on 2mm -

Laser Parameters scratching

Color  Process Power (%)  Speed (%)  ppi/Hz
red Cut CO2 8 0.8 5000
Passes Air Assist Z-Offset Advanced
1 on 1 mm  -

Laser Parameters cutting

Color  Process  Power (%)  Speed (%)  ppi/Hz
blue Cut CO2 95 0.8 5000
Passes Air Assist Z-offset Advanced
1 on - -
print-settings-troglass-metallic
Langkah 3

Step 3: Design TroGlass Metallic

Send the job for the TroGlass Metallic ring to the laser using the driver settings below.

Process mode Resolution Cut line Halftone Others
Standard 600dpi none - -
laser-cutting-troglass-metallic
Langkah 4

Step 4: Engraving TroGlass Metallic

Put the TroGlass Metallic sheet on the acrylic cutting table and engrave the job using the parameters below:

Laser Parameters engraving

Color Process Power (%)
Speed (%)
ppi/Hz 
black Engrave CO2 16 20 600
Passes Air Assist Z-Offset Advanced
1 on 1 mm -

Laser Parameters cutting

Color Process Power (%) Speed (%) ppi/Hz
Red Cut Co2 50 0.2 5000
Passes Air Assist Z-Offset Advanced
1 on - -

Tip: We used the JobControl® parameters for TroGlass optimized for quality.

print-settings-solidwood-maple
Langkah 5

Step 5: Design relief engraving

Finally, send the files for 3-dimensional wood engravings and the other wooden parts to the laser:

Process mode Resolution Cut line Halftone Others
Standard 500dpi None - -
relief-engraving-wood
Langkah 6

Step 6: Laser process relief engraving

Laser Parameters engraving

Color Process Power (%) Speed (%) ppi/Hz
Black Engrave CO2 100 30 500
Passes Air Assist Z-Offset Advanced
3 (!!) On - -

Laser Parameters cutting

Color Process Power (%) Speed (%) ppi / Hz
Red Cut CO2 100 1 1000
Passes Air Assist Z-Offset Advanced
1 On - -

Tip:
When engraving deeply into wood, it can be helpful to cut the job first and engrave the job afterwards.

assembly-laser-engraved-balloon-trophy
Langkah 7

Step 7: Cleaning and assembling

Clean the two acrylic pieces with a damp cloth. The wood relief engraving can be cleaned best with some water and a tooth brush. Here you can find tips for correct cleaning.

Put the acrylic glue on the engraved ring of the base plate and position the TroGlass Metallic ring on it. Press down firmly and allow the glue to cure.
Put double-sided adhesive tape or dots where the wooden relief shall be positioned and fix it.

Take the wooden spacer and apply double-sided adhesive tape on both sides. Position it on the left and the right of the black base plate. Make sure to have a rectangular contact surface so that the trophy stands upright.

Finally, fix the lettering "winner" and the corresponding back on the spacers to complete this elegant trophy.

trotec-inspiration-trophy

Inspiration

Combine other types of solid wood and TroGlass materials to adapt the trophy to your customers' requirements.

Seri Speedy
Pengukir dan pemotong laser yang ideal untuk personalisasi.

Temukan pengukir dan pemotong laser

Pertanyaan tentang aplikasi atau pengaturan?
Kami dengan senang hati akan memberikan saran kepada Anda mulai dari A untuk Air Assist hingga Z untuk z-offset.

Hubungi kami
Anggota kebanggaan troGROUP Logo